/**
* SPDX-FileCopyrightText: 2023 Espressif Systems (Shanghai) CO LTD
*
* SPDX-License-Identifier: Apache-2.0
*/
#pragma once
#include <stdint.h>
#ifdef __cplusplus
extern "C" {
#endif
/** Group: User-defined control registers */
/** Type of cmd register
* SPI1 memory command register
*/
typedef union {
struct {
/** mst_st : RO; bitpos: [3:0]; default: 0;
* The current status of SPI1 master FSM.
*/
uint32_t mst_st:4;
/** slv_st : RO; bitpos: [7:4]; default: 0;
* The current status of SPI1 slave FSM: mspi_st. 0: idle state, 1: preparation state,
* 2: send command state, 3: send address state, 4: wait state, 5: read data state,
* 6:write data state, 7: done state, 8: read data end state.
*/
uint32_t slv_st:4;
uint32_t reserved_8:9;
/** flash_pe : R/W/SC; bitpos: [17]; default: 0;
* In user mode, it is set to indicate that program/erase operation will be triggered.
* The bit is combined with spi1_mem_s_usr bit. The bit will be cleared once the
* operation done.1: enable 0: disable.
*/
uint32_t flash_pe:1;
/** usr : R/W/SC; bitpos: [18]; default: 0;
* User define command enable. An operation will be triggered when the bit is set.
* The bit will be cleared once the operation done.1: enable 0: disable.
*/
uint32_t usr:1;
/** flash_hpm : R/W/SC; bitpos: [19]; default: 0;
* Drive Flash into high performance mode. The bit will be cleared once the operation
* done.1: enable 0: disable.
*/
uint32_t flash_hpm:1;
/** flash_res : R/W/SC; bitpos: [20]; default: 0;
* This bit combined with reg_resandres bit releases Flash from the power-down state
* or high performance mode and obtains the devices ID. The bit will be cleared once
* the operation done.1: enable 0: disable.
*/
uint32_t flash_res:1;
/** flash_dp : R/W/SC; bitpos: [21]; default: 0;
* Drive Flash into power down. An operation will be triggered when the bit is set.
* The bit will be cleared once the operation done.1: enable 0: disable.
*/
uint32_t flash_dp:1;
/** flash_ce : R/W/SC; bitpos: [22]; default: 0;
* Chip erase enable. Chip erase operation will be triggered when the bit is set. The
* bit will be cleared once the operation done.1: enable 0: disable.
*/
uint32_t flash_ce:1;
/** flash_be : R/W/SC; bitpos: [23]; default: 0;
* Block erase enable(32KB) . Block erase operation will be triggered when the bit is
* set. The bit will be cleared once the operation done.1: enable 0: disable.
*/
uint32_t flash_be:1;
/** flash_se : R/W/SC; bitpos: [24]; default: 0;
* Sector erase enable(4KB). Sector erase operation will be triggered when the bit is
* set. The bit will be cleared once the operation done.1: enable 0: disable.
*/
uint32_t flash_se:1;
/** flash_pp : R/W/SC; bitpos: [25]; default: 0;
* Page program enable(1 byte ~256 bytes data to be programmed). Page program
* operation will be triggered when the bit is set. The bit will be cleared once the
* operation done .1: enable 0: disable.
*/
uint32_t flash_pp:1;
/** flash_wrsr : R/W/SC; bitpos: [26]; default: 0;
* Write status register enable. Write status operation will be triggered when the
* bit is set. The bit will be cleared once the operation done.1: enable 0: disable.
*/
uint32_t flash_wrsr:1;
/** flash_rdsr : R/W/SC; bitpos: [27]; default: 0;
* Read status register-1. Read status operation will be triggered when the bit is
* set. The bit will be cleared once the operation done.1: enable 0: disable.
*/
uint32_t flash_rdsr:1;
/** flash_rdid : R/W/SC; bitpos: [28]; default: 0;
* Read JEDEC ID . Read ID command will be sent when the bit is set. The bit will be
* cleared once the operation done. 1: enable 0: disable.
*/
uint32_t flash_rdid:1;
/** flash_wrdi : R/W/SC; bitpos: [29]; default: 0;
* Write flash disable. Write disable command will be sent when the bit is set. The
* bit will be cleared once the operation done. 1: enable 0: disable.
*/
uint32_t flash_wrdi:1;
/** flash_wren : R/W/SC; bitpos: [30]; default: 0;
* Write flash enable. Write enable command will be sent when the bit is set. The bit
* will be cleared once the operation done. 1: enable 0: disable.
*/
uint32_t flash_wren:1;
/** flash_read : R/W/SC; bitpos: [31]; default: 0;
* Read flash enable. Read flash operation will be triggered when the bit is set. The
* bit will be cleared once the operation done. 1: enable 0: disable.
*/
uint32_t flash_read:1;
};
uint32_t val;
} spi1_mem_s_cmd_reg_t;
/** Type of addr register
* SPI1 address register
*/
typedef union {
struct {
/** usr_addr_value : R/W; bitpos: [31:0]; default: 0;
* In user mode, it is the memory address. other then the bit0-bit23 is the memory
* address, the bit24-bit31 are the byte length of a transfer.
*/
uint32_t usr_addr_value:32;
};
uint32_t val;
} spi1_mem_s_addr_reg_t;
/** Type of user register
* SPI1 user register.
*/
typedef union {
struct {
uint32_t reserved_0:9;
/** ck_out_edge : R/W; bitpos: [9]; default: 0;
* the bit combined with spi1_mem_s_mosi_delay_mode bits to set mosi signal delay mode.
*/
uint32_t ck_out_edge:1;
uint32_t reserved_10:2;
/** fwrite_dual : R/W; bitpos: [12]; default: 0;
* In the write operations read-data phase apply 2 signals
*/
uint32_t fwrite_dual:1;
/** fwrite_quad : R/W; bitpos: [13]; default: 0;
* In the write operations read-data phase apply 4 signals
*/
uint32_t fwrite_quad:1;
/** fwrite_dio : R/W; bitpos: [14]; default: 0;
* In the write operations address phase and read-data phase apply 2 signals.
*/
uint32_t fwrite_dio:1;
/** fwrite_qio : R/W; bitpos: [15]; default: 0;
* In the write operations address phase and read-data phase apply 4 signals.
*/
uint32_t fwrite_qio:1;
uint32_t reserved_16:8;
/** usr_miso_highpart : R/W; bitpos: [24]; default: 0;
* read-data phase only access to high-part of the buffer spi1_mem_s_w8~spi1_mem_s_w15. 1:
* enable 0: disable.
*/
uint32_t usr_miso_highpart:1;
/** usr_mosi_highpart : R/W; bitpos: [25]; default: 0;
* write-data phase only access to high-part of the buffer spi1_mem_s_w8~spi1_mem_s_w15. 1:
* enable 0: disable.
*/
uint32_t usr_mosi_highpart:1;
/** usr_dummy_idle : R/W; bitpos: [26]; default: 0;
* SPI clock is disable in dummy phase when the bit is enable.
*/
uint32_t usr_dummy_idle:1;
/** usr_mosi : R/W; bitpos: [27]; default: 0;
* This bit enable the write-data phase of an operation.
*/
uint32_t usr_mosi:1;
/** usr_miso : R/W; bitpos: [28]; default: 0;
* This bit enable the read-data phase of an operation.
*/
uint32_t usr_miso:1;
/** usr_dummy : R/W; bitpos: [29]; default: 0;
* This bit enable the dummy phase of an operation.
*/
uint32_t usr_dummy:1;
/** usr_addr : R/W; bitpos: [30]; default: 0;
* This bit enable the address phase of an operation.
*/
uint32_t usr_addr:1;
/** usr_command : R/W; bitpos: [31]; default: 1;
* This bit enable the command phase of an operation.
*/
uint32_t usr_command:1;
};
uint32_t val;
} spi1_mem_s_user_reg_t;
/** Type of user1 register
* SPI1 user1 register.
*/
typedef union {
struct {
/** usr_dummy_cyclelen : R/W; bitpos: [5:0]; default: 7;
* The length in spi1_mem_s_clk cycles of dummy phase. The register value shall be
* (cycle_num-1).
*/
uint32_t usr_dummy_cyclelen:6;
uint32_t reserved_6:20;
/** usr_addr_bitlen : R/W; bitpos: [31:26]; default: 23;
* The length in bits of address phase. The register value shall be (bit_num-1).
*/
uint32_t usr_addr_bitlen:6;
};
uint32_t val;
} spi1_mem_s_user1_reg_t;
/** Type of user2 register
* SPI1 user2 register.
*/
typedef union {
struct {
/** usr_command_value : R/W; bitpos: [15:0]; default: 0;
* The value of command.
*/
uint32_t usr_command_value:16;
uint32_t reserved_16:12;
/** usr_command_bitlen : R/W; bitpos: [31:28]; default: 7;
* The length in bits of command phase. The register value shall be (bit_num-1)
*/
uint32_t usr_command_bitlen:4;
};
uint32_t val;
} spi1_mem_s_user2_reg_t;
/** Group: Control and configuration registers */
/** Type of ctrl register
* SPI1 control register.
*/
typedef union {
struct {
uint32_t reserved_0:2;
/** fdummy_rin : R/W; bitpos: [2]; default: 1;
* In the dummy phase of a MSPI read data transfer when accesses to flash, the signal
* level of SPI bus is output by the MSPI controller.
*/
uint32_t fdummy_rin:1;
/** fdummy_wout : R/W; bitpos: [3]; default: 1;
* In the dummy phase of a MSPI write data transfer when accesses to flash, the signal
* level of SPI bus is output by the MSPI controller.
*/
uint32_t fdummy_wout:1;
/** fdout_oct : R/W; bitpos: [4]; default: 0;
* Apply 8 signals during write-data phase 1:enable 0: disable
*/
uint32_t fdout_oct:1;
/** fdin_oct : R/W; bitpos: [5]; default: 0;
* Apply 8 signals during read-data phase 1:enable 0: disable
*/
uint32_t fdin_oct:1;
/** faddr_oct : R/W; bitpos: [6]; default: 0;
* Apply 8 signals during address phase 1:enable 0: disable
*/
uint32_t faddr_oct:1;
uint32_t reserved_7:1;
/** fcmd_quad : R/W; bitpos: [8]; default: 0;
* Apply 4 signals during command phase 1:enable 0: disable
*/
uint32_t fcmd_quad:1;
/** fcmd_oct : R/W; bitpos: [9]; default: 0;
* Apply 8 signals during command phase 1:enable 0: disable
*/
uint32_t fcmd_oct:1;
/** fcs_crc_en : R/W; bitpos: [10]; default: 0;
* For SPI1, initialize crc32 module before writing encrypted data to flash. Active
* low.
*/
uint32_t fcs_crc_en:1;
/** tx_crc_en : R/W; bitpos: [11]; default: 0;
* For SPI1, enable crc32 when writing encrypted data to flash. 1: enable 0:disable
*/
uint32_t tx_crc_en:1;
uint32_t reserved_12:1;
/** fastrd_mode : R/W; bitpos: [13]; default: 1;
* This bit enable the bits: spi1_mem_s_fread_qio, spi1_mem_s_fread_dio, spi1_mem_s_fread_qout
* and spi1_mem_s_fread_dout. 1: enable 0: disable.
*/
uint32_t fastrd_mode:1;
/** fread_dual : R/W; bitpos: [14]; default: 0;
* In the read operations, read-data phase apply 2 signals. 1: enable 0: disable.
*/
uint32_t fread_dual:1;
/** resandres : R/W; bitpos: [15]; default: 1;
* The Device ID is read out to SPI1_MEM_S_RD_STATUS register, this bit combine with
* spi1_mem_s_flash_res bit. 1: enable 0: disable.
*/
uint32_t resandres:1;
uint32_t reserved_16:2;
/** q_pol : R/W; bitpos: [18]; default: 1;
* The bit is used to set MISO line polarity, 1: high 0, low
*/
uint32_t q_pol:1;
/** d_pol : R/W; bitpos: [19]; default: 1;
* The bit is used to set MOSI line polarity, 1: high 0, low
*/
uint32_t d_pol:1;
/** fread_quad : R/W; bitpos: [20]; default: 0;
* In the read operations read-data phase apply 4 signals. 1: enable 0: disable.
*/
uint32_t fread_quad:1;
/** wp_reg : R/W; bitpos: [21]; default: 1;
* Write protect signal output when SPI is idle. 1: output high, 0: output low.
*/
uint32_t wp_reg:1;
/** wrsr_2b : R/W; bitpos: [22]; default: 0;
* two bytes data will be written to status register when it is set. 1: enable 0:
* disable.
*/
uint32_t wrsr_2b:1;
/** fread_dio : R/W; bitpos: [23]; default: 0;
* In the read operations address phase and read-data phase apply 2 signals. 1: enable
* 0: disable.
*/
uint32_t fread_dio:1;
/** fread_qio : R/W; bitpos: [24]; default: 0;
* In the read operations address phase and read-data phase apply 4 signals. 1: enable
* 0: disable.
*/
uint32_t fread_qio:1;
uint32_t reserved_25:7;
};
uint32_t val;
} spi1_mem_s_ctrl_reg_t;
/** Type of ctrl1 register
* SPI1 control1 register.
*/
typedef union {
struct {
/** clk_mode : R/W; bitpos: [1:0]; default: 0;
* SPI clock mode bits. 0: SPI clock is off when CS inactive 1: SPI clock is delayed
* one cycle after CS inactive 2: SPI clock is delayed two cycles after CS inactive 3:
* SPI clock is alwasy on.
*/
uint32_t clk_mode:2;
/** cs_hold_dly_res : R/W; bitpos: [11:2]; default: 1023;
* After RES/DP/HPM command is sent, SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 512)
* SPI_CLK cycles.
*/
uint32_t cs_hold_dly_res:10;
uint32_t reserved_12:20;
};
uint32_t val;
} spi1_mem_s_ctrl1_reg_t;
/** Type of ctrl2 register
* SPI1 control2 register.
*/
typedef union {
struct {
uint32_t reserved_0:31;
/** sync_reset : WT; bitpos: [31]; default: 0;
* The FSM will be reset.
*/
uint32_t sync_reset:1;
};
uint32_t val;
} spi1_mem_s_ctrl2_reg_t;
/** Type of clock register
* SPI1 clock division control register.
*/
typedef union {
struct {
/** clkcnt_l : R/W; bitpos: [7:0]; default: 3;
* In the master mode it must be equal to spi1_mem_s_clkcnt_N.
*/
uint32_t clkcnt_l:8;
/** clkcnt_h : R/W; bitpos: [15:8]; default: 1;
* In the master mode it must be floor((spi1_mem_s_clkcnt_N+1)/2-1).
*/
uint32_t clkcnt_h:8;
/** clkcnt_n : R/W; bitpos: [23:16]; default: 3;
* In the master mode it is the divider of spi1_mem_s_clk. So spi1_mem_s_clk frequency is
* system/(spi1_mem_s_clkcnt_N+1)
*/
uint32_t clkcnt_n:8;
uint32_t reserved_24:7;
/** clk_equ_sysclk : R/W; bitpos: [31]; default: 0;
* reserved
*/
uint32_t clk_equ_sysclk:1;
};
uint32_t val;
} spi1_mem_s_clock_reg_t;
/** Type of mosi_dlen register
* SPI1 send data bit length control register.
*/
typedef union {
struct {
/** usr_mosi_dbitlen : R/W; bitpos: [9:0]; default: 0;
* The length in bits of write-data. The register value shall be (bit_num-1).
*/
uint32_t usr_mosi_dbitlen:10;
uint32_t reserved_10:22;
};
uint32_t val;
} spi1_mem_s_mosi_dlen_reg_t;
/** Type of miso_dlen register
* SPI1 receive data bit length control register.
*/
typedef union {
struct {
/** usr_miso_dbitlen : R/W; bitpos: [9:0]; default: 0;
* The length in bits of read-data. The register value shall be (bit_num-1).
*/
uint32_t usr_miso_dbitlen:10;
uint32_t reserved_10:22;
};
uint32_t val;
} spi1_mem_s_miso_dlen_reg_t;
/** Type of rd_status register
* SPI1 status register.
*/
typedef union {
struct {
/** status : R/W/SS; bitpos: [15:0]; default: 0;
* The value is stored when set spi1_mem_s_flash_rdsr bit and spi1_mem_s_flash_res bit.
*/
uint32_t status:16;
/** wb_mode : R/W; bitpos: [23:16]; default: 0;
* Mode bits in the flash fast read mode it is combined with spi1_mem_s_fastrd_mode bit.
*/
uint32_t wb_mode:8;
uint32_t reserved_24:8;
};
uint32_t val;
} spi1_mem_s_rd_status_reg_t;
/** Type of misc register
* SPI1 misc register
*/
typedef union {
struct {
/** cs0_dis : R/W; bitpos: [0]; default: 0;
* SPI_CS0 pin enable, 1: disable SPI_CS0, 0: SPI_CS0 pin is active to select SPI
* device, such as flash, external RAM and so on.
*/
uint32_t cs0_dis:1;
/** cs1_dis : R/W; bitpos: [1]; default: 1;
* SPI_CS1 pin enable, 1: disable SPI_CS1, 0: SPI_CS1 pin is active to select SPI
* device, such as flash, external RAM and so on.
*/
uint32_t cs1_dis:1;
uint32_t reserved_2:7;
/** ck_idle_edge : R/W; bitpos: [9]; default: 0;
* 1: spi clk line is high when idle 0: spi clk line is low when idle
*/
uint32_t ck_idle_edge:1;
/** cs_keep_active : R/W; bitpos: [10]; default: 0;
* spi cs line keep low when the bit is set.
*/
uint32_t cs_keep_active:1;
uint32_t reserved_11:21;
};
uint32_t val;
} spi1_mem_s_misc_reg_t;
/** Type of cache_fctrl register
* SPI1 bit mode control register.
*/
typedef union {
struct {
uint32_t reserved_0:1;
/** cache_usr_addr_4byte : R/W; bitpos: [1]; default: 0;
* For SPI1, cache read flash with 4 bytes address, 1: enable, 0:disable.
*/
uint32_t cache_usr_addr_4byte:1;
uint32_t reserved_2:1;
/** fdin_dual : R/W; bitpos: [3]; default: 0;
* For SPI1, din phase apply 2 signals. 1: enable 0: disable. The bit is the same with
* spi1_mem_s_fread_dio.
*/
uint32_t fdin_dual:1;
/** fdout_dual : R/W; bitpos: [4]; default: 0;
* For SPI1, dout phase apply 2 signals. 1: enable 0: disable. The bit is the same
* with spi1_mem_s_fread_dio.
*/
uint32_t fdout_dual:1;
/** faddr_dual : R/W; bitpos: [5]; default: 0;
* For SPI1, address phase apply 2 signals. 1: enable 0: disable. The bit is the same
* with spi1_mem_s_fread_dio.
*/
uint32_t faddr_dual:1;
/** fdin_quad : R/W; bitpos: [6]; default: 0;
* For SPI1, din phase apply 4 signals. 1: enable 0: disable. The bit is the same
* with spi1_mem_s_fread_qio.
*/
uint32_t fdin_quad:1;
/** fdout_quad : R/W; bitpos: [7]; default: 0;
* For SPI1, dout phase apply 4 signals. 1: enable 0: disable. The bit is the same
* with spi1_mem_s_fread_qio.
*/
uint32_t fdout_quad:1;
/** faddr_quad : R/W; bitpos: [8]; default: 0;
* For SPI1, address phase apply 4 signals. 1: enable 0: disable. The bit is the same
* with spi1_mem_s_fread_qio.
*/
uint32_t faddr_quad:1;
uint32_t reserved_9:23;
};
uint32_t val;
} spi1_mem_s_cache_fctrl_reg_t;
/** Type of flash_waiti_ctrl register
* SPI1 wait idle control register
*/
typedef union {
struct {
/** waiti_en : R/W; bitpos: [0]; default: 1;
* 1: The hardware will wait idle after SE/PP/WRSR automatically, and hardware auto
* Suspend/Resume can be enabled. 0: The functions of hardware wait idle and auto
* Suspend/Resume are not supported.
*/
uint32_t waiti_en:1;
/** waiti_dummy : R/W; bitpos: [1]; default: 0;
* The dummy phase enable when wait flash idle (RDSR)
*/
uint32_t waiti_dummy:1;
/** waiti_addr_en : R/W; bitpos: [2]; default: 0;
* 1: Output address 0 in RDSR or read SUS command transfer. 0: Do not send out
* address in RDSR or read SUS command transfer.
*/
uint32_t waiti_addr_en:1;
/** waiti_addr_cyclelen : R/W; bitpos: [4:3]; default: 0;
* When SPI1_MEM_S_WAITI_ADDR_EN is set, the cycle length of sent out address is
* (SPI1_MEM_S_WAITI_ADDR_CYCLELEN[1:0] + 1) SPI bus clock cycles. It is not active when
* SPI1_MEM_S_WAITI_ADDR_EN is cleared.
*/
uint32_t waiti_addr_cyclelen:2;
uint32_t reserved_5:4;
/** waiti_cmd_2b : R/W; bitpos: [9]; default: 0;
* 1:The wait idle command bit length is 16. 0: The wait idle command bit length is 8.
*/
uint32_t waiti_cmd_2b:1;
/** waiti_dummy_cyclelen : R/W; bitpos: [15:10]; default: 0;
* The dummy cycle length when wait flash idle(RDSR).
*/
uint32_t waiti_dummy_cyclelen:6;
/** waiti_cmd : R/W; bitpos: [31:16]; default: 5;
* The command value to wait flash idle(RDSR).
*/
uint32_t waiti_cmd:16;
};
uint32_t val;
} spi1_mem_s_flash_waiti_ctrl_reg_t;
/** Type of flash_sus_ctrl register
* SPI1 flash suspend control register
*/
typedef union {
struct {
/** flash_per : R/W/SC; bitpos: [0]; default: 0;
* program erase resume bit, program erase suspend operation will be triggered when
* the bit is set. The bit will be cleared once the operation done.1: enable 0:
* disable.
*/
uint32_t flash_per:1;
/** flash_pes : R/W/SC; bitpos: [1]; default: 0;
* program erase suspend bit, program erase suspend operation will be triggered when
* the bit is set. The bit will be cleared once the operation done.1: enable 0:
* disable.
*/
uint32_t flash_pes:1;
/** flash_per_wait_en : R/W; bitpos: [2]; default: 0;
* 1: SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 4 or *128) SPI_CLK cycles after
* program erase resume command is sent. 0: SPI1 does not wait after program erase
* resume command is sent.
*/
uint32_t flash_per_wait_en:1;
/** flash_pes_wait_en : R/W; bitpos: [3]; default: 0;
* 1: SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 4 or *128) SPI_CLK cycles after
* program erase suspend command is sent. 0: SPI1 does not wait after program erase
* suspend command is sent.
*/
uint32_t flash_pes_wait_en:1;
/** pes_per_en : R/W; bitpos: [4]; default: 0;
* Set this bit to enable PES end triggers PER transfer option. If this bit is 0,
* application should send PER after PES is done.
*/
uint32_t pes_per_en:1;
/** flash_pes_en : R/W; bitpos: [5]; default: 0;
* Set this bit to enable Auto-suspending function.
*/
uint32_t flash_pes_en:1;
/** pesr_end_msk : R/W; bitpos: [21:6]; default: 128;
* The mask value when check SUS/SUS1/SUS2 status bit. If the read status value is
* status_in[15:0](only status_in[7:0] is valid when only one byte of data is read
* out, status_in[15:0] is valid when two bytes of data are read out), SUS/SUS1/SUS2 =
* status_in[15:0]^ SPI1_MEM_S_PESR_END_MSK[15:0].
*/
uint32_t pesr_end_msk:16;
/** fmem_rd_sus_2b : R/W; bitpos: [22]; default: 0;
* 1: Read two bytes when check flash SUS/SUS1/SUS2 status bit. 0: Read one byte when
* check flash SUS/SUS1/SUS2 status bit
*/
uint32_t fmem_rd_sus_2b:1;
/** per_end_en : R/W; bitpos: [23]; default: 0;
* 1: Both WIP and SUS/SUS1/SUS2 bits should be checked to insure the resume status of
* flash. 0: Only need to check WIP is 0.
*/
uint32_t per_end_en:1;
/** pes_end_en : R/W; bitpos: [24]; default: 0;
* 1: Both WIP and SUS/SUS1/SUS2 bits should be checked to insure the suspend status
* of flash. 0: Only need to check WIP is 0.
*/
uint32_t pes_end_en:1;
/** sus_timeout_cnt : R/W; bitpos: [31:25]; default: 4;
* When SPI1 checks SUS/SUS1/SUS2 bits fail for SPI1_MEM_S_SUS_TIMEOUT_CNT[6:0] times, it
* will be treated as check pass.
*/
uint32_t sus_timeout_cnt:7;
};
uint32_t val;
} spi1_mem_s_flash_sus_ctrl_reg_t;
/** Type of flash_sus_cmd register
* SPI1 flash suspend command register
*/
typedef union {
struct {
/** flash_pes_command : R/W; bitpos: [15:0]; default: 30069;
* Program/Erase suspend command.
*/
uint32_t flash_pes_command:16;
/** wait_pesr_command : R/W; bitpos: [31:16]; default: 5;
* Flash SUS/SUS1/SUS2 status bit read command. The command should be sent when
* SUS/SUS1/SUS2 bit should be checked to insure the suspend or resume status of flash.
*/
uint32_t wait_pesr_command:16;
};
uint32_t val;
} spi1_mem_s_flash_sus_cmd_reg_t;
/** Type of sus_status register
* SPI1 flash suspend status register
*/
typedef union {
struct {
/** flash_sus : R/W/SS/SC; bitpos: [0]; default: 0;
* The status of flash suspend, only used in SPI1.
*/
uint32_t flash_sus:1;
/** wait_pesr_cmd_2b : R/W; bitpos: [1]; default: 0;
* 1: SPI1 sends out SPI1_MEM_S_WAIT_PESR_COMMAND[15:0] to check SUS/SUS1/SUS2 bit. 0:
* SPI1 sends out SPI1_MEM_S_WAIT_PESR_COMMAND[7:0] to check SUS/SUS1/SUS2 bit.
*/
uint32_t wait_pesr_cmd_2b:1;
/** flash_hpm_dly_128 : R/W; bitpos: [2]; default: 0;
* 1: SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 128) SPI_CLK cycles after HPM
* command is sent. 0: SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 4) SPI_CLK cycles
* after HPM command is sent.
*/
uint32_t flash_hpm_dly_128:1;
/** flash_res_dly_128 : R/W; bitpos: [3]; default: 0;
* 1: SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 128) SPI_CLK cycles after RES
* command is sent. 0: SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 4) SPI_CLK cycles
* after RES command is sent.
*/
uint32_t flash_res_dly_128:1;
/** flash_dp_dly_128 : R/W; bitpos: [4]; default: 0;
* 1: SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 128) SPI_CLK cycles after DP
* command is sent. 0: SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 4) SPI_CLK cycles
* after DP command is sent.
*/
uint32_t flash_dp_dly_128:1;
/** flash_per_dly_128 : R/W; bitpos: [5]; default: 0;
* Valid when SPI1_MEM_S_FLASH_PER_WAIT_EN is 1. 1: SPI1 waits
* (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 128) SPI_CLK cycles after PER command is sent. 0:
* SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 4) SPI_CLK cycles after PER command is
* sent.
*/
uint32_t flash_per_dly_128:1;
/** flash_pes_dly_128 : R/W; bitpos: [6]; default: 0;
* Valid when SPI1_MEM_S_FLASH_PES_WAIT_EN is 1. 1: SPI1 waits
* (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 128) SPI_CLK cycles after PES command is sent. 0:
* SPI1 waits (SPI1_MEM_S_CS_HOLD_DELAY_RES[9:0] * 4) SPI_CLK cycles after PES command is
* sent.
*/
uint32_t flash_pes_dly_128:1;
/** spi0_lock_en : R/W; bitpos: [7]; default: 0;
* 1: Enable SPI0 lock SPI0/1 arbiter option. 0: Disable it.
*/
uint32_t spi0_lock_en:1;
uint32_t reserved_8:7;
/** flash_pesr_cmd_2b : R/W; bitpos: [15]; default: 0;
* 1: The bit length of Program/Erase Suspend/Resume command is 16. 0: The bit length
* of Program/Erase Suspend/Resume command is 8.
*/
uint32_t flash_pesr_cmd_2b:1;
/** flash_per_command : R/W; bitpos: [31:16]; default: 31354;
* Program/Erase resume command.
*/
uint32_t flash_per_command:16;
};
uint32_t val;
} spi1_mem_s_sus_status_reg_t;
/** Type of ddr register
* SPI1 DDR control register
*/
typedef union {
struct {
/** fmem_ddr_en : R/W; bitpos: [0]; default: 0;
* 1: in ddr mode, 0 in sdr mode
*/
uint32_t fmem_ddr_en:1;
/** fmem_var_dummy : R/W; bitpos: [1]; default: 0;
* Set the bit to enable variable dummy cycle in spi ddr mode.
*/
uint32_t fmem_var_dummy:1;
/** fmem_ddr_rdat_swp : R/W; bitpos: [2]; default: 0;
* Set the bit to reorder rx data of the word in spi ddr mode.
*/
uint32_t fmem_ddr_rdat_swp:1;
/** fmem_ddr_wdat_swp : R/W; bitpos: [3]; default: 0;
* Set the bit to reorder tx data of the word in spi ddr mode.
*/
uint32_t fmem_ddr_wdat_swp:1;
/** fmem_ddr_cmd_dis : R/W; bitpos: [4]; default: 0;
* the bit is used to disable dual edge in command phase when ddr mode.
*/
uint32_t fmem_ddr_cmd_dis:1;
/** fmem_outminbytelen : R/W; bitpos: [11:5]; default: 1;
* It is the minimum output data length in the panda device.
*/
uint32_t fmem_outminbytelen:7;
uint32_t reserved_12:2;
/** fmem_usr_ddr_dqs_thd : R/W; bitpos: [20:14]; default: 0;
* The delay number of data strobe which from memory based on SPI clock.
*/
uint32_t fmem_usr_ddr_dqs_thd:7;
/** fmem_ddr_dqs_loop : R/W; bitpos: [21]; default: 0;
* 1: Do not need the input of SPI_DQS signal, SPI0 starts to receive data when
* spi0_slv_st is in SPI1_MEM_S_DIN state. It is used when there is no SPI_DQS signal or
* SPI_DQS signal is not stable. 0: SPI0 starts to store data at the positive and
* negative edge of SPI_DQS.
*/
uint32_t fmem_ddr_dqs_loop:1;
uint32_t reserved_22:2;
/** fmem_clk_diff_en : R/W; bitpos: [24]; default: 0;
* Set this bit to enable the differential SPI_CLK#.
*/
uint32_t fmem_clk_diff_en:1;
uint32_t reserved_25:1;
/** fmem_dqs_ca_in : R/W; bitpos: [26]; default: 0;
* Set this bit to enable the input of SPI_DQS signal in SPI phases of CMD and ADDR.
*/
uint32_t fmem_dqs_ca_in:1;
/** fmem_hyperbus_dummy_2x : R/W; bitpos: [27]; default: 0;
* Set this bit to enable the vary dummy function in SPI HyperBus mode, when SPI0
* accesses flash or SPI1 accesses flash or sram.
*/
uint32_t fmem_hyperbus_dummy_2x:1;
/** fmem_clk_diff_inv : R/W; bitpos: [28]; default: 0;
* Set this bit to invert SPI_DIFF when accesses to flash. .
*/
uint32_t fmem_clk_diff_inv:1;
/** fmem_octa_ram_addr : R/W; bitpos: [29]; default: 0;
* Set this bit to enable octa_ram address out when accesses to flash, which means
* ADDR_OUT[31:0] = {spi_usr_addr_value[25:4], 6'd0, spi_usr_addr_value[3:1], 1'b0}.
*/
uint32_t fmem_octa_ram_addr:1;
/** fmem_hyperbus_ca : R/W; bitpos: [30]; default: 0;
* Set this bit to enable HyperRAM address out when accesses to flash, which means
* ADDR_OUT[31:0] = {spi_usr_addr_value[19:4], 13'd0, spi_usr_addr_value[3:1]}.
*/
uint32_t fmem_hyperbus_ca:1;
uint32_t reserved_31:1;
};
uint32_t val;
} spi1_mem_s_ddr_reg_t;
/** Type of clock_gate register
* SPI1 clk_gate register
*/
typedef union {
struct {
/** clk_en : R/W; bitpos: [0]; default: 1;
* Register clock gate enable signal. 1: Enable. 0: Disable.
*/
uint32_t clk_en:1;
uint32_t reserved_1:31;
};
uint32_t val;
} spi1_mem_s_clock_gate_reg_t;
/** Group: Status register */
/** Type of tx_crc register
* SPI1 TX CRC data register.
*/
typedef union {
struct {
/** tx_crc_data : RO; bitpos: [31:0]; default: 4294967295;
* For SPI1, the value of crc32.
*/
uint32_t tx_crc_data:32;
};
uint32_t val;
} spi1_mem_s_tx_crc_reg_t;
/** Group: Memory data buffer register */
/** Type of w0 register
* SPI1 memory data buffer0
*/
typedef union {
struct {
/** buf0 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf0:32;
};
uint32_t val;
} spi1_mem_s_w0_reg_t;
/** Type of w1 register
* SPI1 memory data buffer1
*/
typedef union {
struct {
/** buf1 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf1:32;
};
uint32_t val;
} spi1_mem_s_w1_reg_t;
/** Type of w2 register
* SPI1 memory data buffer2
*/
typedef union {
struct {
/** buf2 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf2:32;
};
uint32_t val;
} spi1_mem_s_w2_reg_t;
/** Type of w3 register
* SPI1 memory data buffer3
*/
typedef union {
struct {
/** buf3 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf3:32;
};
uint32_t val;
} spi1_mem_s_w3_reg_t;
/** Type of w4 register
* SPI1 memory data buffer4
*/
typedef union {
struct {
/** buf4 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf4:32;
};
uint32_t val;
} spi1_mem_s_w4_reg_t;
/** Type of w5 register
* SPI1 memory data buffer5
*/
typedef union {
struct {
/** buf5 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf5:32;
};
uint32_t val;
} spi1_mem_s_w5_reg_t;
/** Type of w6 register
* SPI1 memory data buffer6
*/
typedef union {
struct {
/** buf6 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf6:32;
};
uint32_t val;
} spi1_mem_s_w6_reg_t;
/** Type of w7 register
* SPI1 memory data buffer7
*/
typedef union {
struct {
/** buf7 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf7:32;
};
uint32_t val;
} spi1_mem_s_w7_reg_t;
/** Type of w8 register
* SPI1 memory data buffer8
*/
typedef union {
struct {
/** buf8 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf8:32;
};
uint32_t val;
} spi1_mem_s_w8_reg_t;
/** Type of w9 register
* SPI1 memory data buffer9
*/
typedef union {
struct {
/** buf9 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf9:32;
};
uint32_t val;
} spi1_mem_s_w9_reg_t;
/** Type of w10 register
* SPI1 memory data buffer10
*/
typedef union {
struct {
/** buf10 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf10:32;
};
uint32_t val;
} spi1_mem_s_w10_reg_t;
/** Type of w11 register
* SPI1 memory data buffer11
*/
typedef union {
struct {
/** buf11 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf11:32;
};
uint32_t val;
} spi1_mem_s_w11_reg_t;
/** Type of w12 register
* SPI1 memory data buffer12
*/
typedef union {
struct {
/** buf12 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf12:32;
};
uint32_t val;
} spi1_mem_s_w12_reg_t;
/** Type of w13 register
* SPI1 memory data buffer13
*/
typedef union {
struct {
/** buf13 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf13:32;
};
uint32_t val;
} spi1_mem_s_w13_reg_t;
/** Type of w14 register
* SPI1 memory data buffer14
*/
typedef union {
struct {
/** buf14 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf14:32;
};
uint32_t val;
} spi1_mem_s_w14_reg_t;
/** Type of w15 register
* SPI1 memory data buffer15
*/
typedef union {
struct {
/** buf15 : R/W/SS; bitpos: [31:0]; default: 0;
* data buffer
*/
uint32_t buf15:32;
};
uint32_t val;
} spi1_mem_s_w15_reg_t;
/** Group: Interrupt registers */
/** Type of int_ena register
* SPI1 interrupt enable register
*/
typedef union {
struct {
/** per_end_int_ena : R/W; bitpos: [0]; default: 0;
* The enable bit for SPI1_MEM_S_PER_END_INT interrupt.
*/
uint32_t per_end_int_ena:1;
/** pes_end_int_ena : R/W; bitpos: [1]; default: 0;
* The enable bit for SPI1_MEM_S_PES_END_INT interrupt.
*/
uint32_t pes_end_int_ena:1;
/** wpe_end_int_ena : R/W; bitpos: [2]; default: 0;
* The enable bit for SPI1_MEM_S_WPE_END_INT interrupt.
*/
uint32_t wpe_end_int_ena:1;
/** slv_st_end_int_ena : R/W; bitpos: [3]; default: 0;
* The enable bit for SPI1_MEM_S_SLV_ST_END_INT interrupt.
*/
uint32_t slv_st_end_int_ena:1;
/** mst_st_end_int_ena : R/W; bitpos: [4]; default: 0;
* The enable bit for SPI1_MEM_S_MST_ST_END_INT interrupt.
*/
uint32_t mst_st_end_int_ena:1;
uint32_t reserved_5:5;
/** brown_out_int_ena : R/W; bitpos: [10]; default: 0;
* The enable bit for SPI1_MEM_S_BROWN_OUT_INT interrupt.
*/
uint32_t brown_out_int_ena:1;
uint32_t reserved_11:21;
};
uint32_t val;
} spi1_mem_s_int_ena_reg_t;
/** Type of int_clr register
* SPI1 interrupt clear register
*/
typedef union {
struct {
/** per_end_int_clr : WT; bitpos: [0]; default: 0;
* The clear bit for SPI1_MEM_S_PER_END_INT interrupt.
*/
uint32_t per_end_int_clr:1;
/** pes_end_int_clr : WT; bitpos: [1]; default: 0;
* The clear bit for SPI1_MEM_S_PES_END_INT interrupt.
*/
uint32_t pes_end_int_clr:1;
/** wpe_end_int_clr : WT; bitpos: [2]; default: 0;
* The clear bit for SPI1_MEM_S_WPE_END_INT interrupt.
*/
uint32_t wpe_end_int_clr:1;
/** slv_st_end_int_clr : WT; bitpos: [3]; default: 0;
* The clear bit for SPI1_MEM_S_SLV_ST_END_INT interrupt.
*/
uint32_t slv_st_end_int_clr:1;
/** mst_st_end_int_clr : WT; bitpos: [4]; default: 0;
* The clear bit for SPI1_MEM_S_MST_ST_END_INT interrupt.
*/
uint32_t mst_st_end_int_clr:1;
uint32_t reserved_5:5;
/** brown_out_int_clr : WT; bitpos: [10]; default: 0;
* The status bit for SPI1_MEM_S_BROWN_OUT_INT interrupt.
*/
uint32_t brown_out_int_clr:1;
uint32_t reserved_11:21;
};
uint32_t val;
} spi1_mem_s_int_clr_reg_t;
/** Type of int_raw register
* SPI1 interrupt raw register
*/
typedef union {
struct {
/** per_end_int_raw : R/WTC/SS; bitpos: [0]; default: 0;
* The raw bit for SPI1_MEM_S_PER_END_INT interrupt. 1: Triggered when Auto Resume
* command (0x7A) is sent and flash is resumed successfully. 0: Others.
*/
uint32_t per_end_int_raw:1;
/** pes_end_int_raw : R/WTC/SS; bitpos: [1]; default: 0;
* The raw bit for SPI1_MEM_S_PES_END_INT interrupt.1: Triggered when Auto Suspend
* command (0x75) is sent and flash is suspended successfully. 0: Others.
*/
uint32_t pes_end_int_raw:1;
/** wpe_end_int_raw : R/WTC/SS; bitpos: [2]; default: 0;
* The raw bit for SPI1_MEM_S_WPE_END_INT interrupt. 1: Triggered when WRSR/PP/SE/BE/CE
* is sent and flash is already idle. 0: Others.
*/
uint32_t wpe_end_int_raw:1;
/** slv_st_end_int_raw : R/WTC/SS; bitpos: [3]; default: 0;
* The raw bit for SPI1_MEM_S_SLV_ST_END_INT interrupt. 1: Triggered when spi1_slv_st is
* changed from non idle state to idle state. It means that SPI_CS raises high. 0:
* Others
*/
uint32_t slv_st_end_int_raw:1;
/** mst_st_end_int_raw : R/WTC/SS; bitpos: [4]; default: 0;
* The raw bit for SPI1_MEM_S_MST_ST_END_INT interrupt. 1: Triggered when spi1_mst_st is
* changed from non idle state to idle state. 0: Others.
*/
uint32_t mst_st_end_int_raw:1;
uint32_t reserved_5:5;
/** brown_out_int_raw : R/WTC/SS; bitpos: [10]; default: 0;
* The raw bit for SPI1_MEM_S_BROWN_OUT_INT interrupt. 1: Triggered condition is that
* chip is loosing power and RTC module sends out brown out close flash request to
* SPI1. After SPI1 sends out suspend command to flash, this interrupt is triggered
* and MSPI returns to idle state. 0: Others.
*/
uint32_t brown_out_int_raw:1;
uint32_t reserved_11:21;
};
uint32_t val;
} spi1_mem_s_int_raw_reg_t;
/** Type of int_st register
* SPI1 interrupt status register
*/
typedef union {
struct {
/** per_end_int_st : RO; bitpos: [0]; default: 0;
* The status bit for SPI1_MEM_S_PER_END_INT interrupt.
*/
uint32_t per_end_int_st:1;
/** pes_end_int_st : RO; bitpos: [1]; default: 0;
* The status bit for SPI1_MEM_S_PES_END_INT interrupt.
*/
uint32_t pes_end_int_st:1;
/** wpe_end_int_st : RO; bitpos: [2]; default: 0;
* The status bit for SPI1_MEM_S_WPE_END_INT interrupt.
*/
uint32_t wpe_end_int_st:1;
/** slv_st_end_int_st : RO; bitpos: [3]; default: 0;
* The status bit for SPI1_MEM_S_SLV_ST_END_INT interrupt.
*/
uint32_t slv_st_end_int_st:1;
/** mst_st_end_int_st : RO; bitpos: [4]; default: 0;
* The status bit for SPI1_MEM_S_MST_ST_END_INT interrupt.
*/
uint32_t mst_st_end_int_st:1;
uint32_t reserved_5:5;
/** brown_out_int_st : RO; bitpos: [10]; default: 0;
* The status bit for SPI1_MEM_S_BROWN_OUT_INT interrupt.
*/
uint32_t brown_out_int_st:1;
uint32_t reserved_11:21;
};
uint32_t val;
} spi1_mem_s_int_st_reg_t;
/** Group: Timing registers */
/** Type of timing_cali register
* SPI1 timing control register
*/
typedef union {
struct {
uint32_t reserved_0:1;
/** timing_cali : R/W; bitpos: [1]; default: 0;
* The bit is used to enable timing auto-calibration for all reading operations.
*/
uint32_t timing_cali:1;
/** extra_dummy_cyclelen : R/W; bitpos: [4:2]; default: 0;
* add extra dummy spi clock cycle length for spi clock calibration.
*/
uint32_t extra_dummy_cyclelen:3;
uint32_t reserved_5:27;
};
uint32_t val;
} spi1_mem_s_timing_cali_reg_t;
/** Group: Version register */
/** Type of date register
* Version control register
*/
typedef union {
struct {
/** date : R/W; bitpos: [27:0]; default: 34673216;
* Version control register
*/
uint32_t date:28;
uint32_t reserved_28:4;
};
uint32_t val;
} spi1_mem_s_date_reg_t;
typedef struct spi1_mem_s_dev_s {
volatile spi1_mem_s_cmd_reg_t cmd;
volatile spi1_mem_s_addr_reg_t addr;
volatile spi1_mem_s_ctrl_reg_t ctrl;
volatile spi1_mem_s_ctrl1_reg_t ctrl1;
volatile spi1_mem_s_ctrl2_reg_t ctrl2;
volatile spi1_mem_s_clock_reg_t clock;
volatile spi1_mem_s_user_reg_t user;
volatile spi1_mem_s_user1_reg_t user1;
volatile spi1_mem_s_user2_reg_t user2;
volatile spi1_mem_s_mosi_dlen_reg_t mosi_dlen;
volatile spi1_mem_s_miso_dlen_reg_t miso_dlen;
volatile spi1_mem_s_rd_status_reg_t rd_status;
uint32_t reserved_030;
volatile spi1_mem_s_misc_reg_t misc;
volatile spi1_mem_s_tx_crc_reg_t tx_crc;
volatile spi1_mem_s_cache_fctrl_reg_t cache_fctrl;
uint32_t reserved_040[6];
volatile spi1_mem_s_w0_reg_t w0;
volatile spi1_mem_s_w1_reg_t w1;
volatile spi1_mem_s_w2_reg_t w2;
volatile spi1_mem_s_w3_reg_t w3;
volatile spi1_mem_s_w4_reg_t w4;
volatile spi1_mem_s_w5_reg_t w5;
volatile spi1_mem_s_w6_reg_t w6;
volatile spi1_mem_s_w7_reg_t w7;
volatile spi1_mem_s_w8_reg_t w8;
volatile spi1_mem_s_w9_reg_t w9;
volatile spi1_mem_s_w10_reg_t w10;
volatile spi1_mem_s_w11_reg_t w11;
volatile spi1_mem_s_w12_reg_t w12;
volatile spi1_mem_s_w13_reg_t w13;
volatile spi1_mem_s_w14_reg_t w14;
volatile spi1_mem_s_w15_reg_t w15;
volatile spi1_mem_s_flash_waiti_ctrl_reg_t flash_waiti_ctrl;
volatile spi1_mem_s_flash_sus_ctrl_reg_t flash_sus_ctrl;
volatile spi1_mem_s_flash_sus_cmd_reg_t flash_sus_cmd;
volatile spi1_mem_s_sus_status_reg_t sus_status;
uint32_t reserved_0a8[6];
volatile spi1_mem_s_int_ena_reg_t int_ena;
volatile spi1_mem_s_int_clr_reg_t int_clr;
volatile spi1_mem_s_int_raw_reg_t int_raw;
volatile spi1_mem_s_int_st_reg_t int_st;
uint32_t reserved_0d0;
volatile spi1_mem_s_ddr_reg_t ddr;
uint32_t reserved_0d8[42];
volatile spi1_mem_s_timing_cali_reg_t timing_cali;
uint32_t reserved_184[31];
volatile spi1_mem_s_clock_gate_reg_t clock_gate;
uint32_t reserved_204[126];
volatile spi1_mem_s_date_reg_t date;
} spi1_mem_s_dev_t;
#ifndef __cplusplus
_Static_assert(sizeof(spi1_mem_s_dev_t) == 0x400, "Invalid size of spi1_mem_s_dev_t structure");
#endif
#ifdef __cplusplus
}
#endif